ALLCOAT Chemical Resistant Coating

High grade, hard wearing epoxy floor coating designed for maximum chemical resistance

Chemical Resistant Coating

Chemical Resistant Coating

5litres – £148.15

ALLCOAT Chemical Resistant Coating is a high grade, 2 pack, hard wearing epoxy floor coating designed for maximum chemical resistance which is also light, fast and flexible. It is ideal where a seamless finish is required. ALLCOAT Chemical Resistant Coating has good resistance to impact abrasion and trafficking. The system is resistant to high temperatures up to 150°C. Slight discolouration may occur at extreme temperatures.

Features & Benefits

  • Maximum chemical resistance
  • Rapid set properties – touch dry in just 5 hours
  • Good abrasion and impact resistance
  • Easy cleaning, including removal of graffiti
  • Light and fast installation – usually just one coat required
  • Resistant to thermal shock & hot water
  • Hygienic – does not support fungus or bacterial growth
  • Attractive range of colours available

Typical Uses

  • Food preparation and manufacturing areas
  • Laboratories
  • Chemical plants
  • Aircraft hangers
  • Vehicle maintenance bays
  • Abattoirs
  • Breweries
  • Mortuaries
  • Bakeries
  • Toilets
  • Operating theatres
  • Any areas where a long lasting, easily cleaned, high chemical resistance finish is essential
SKU: Acitec. Categories: , .

Preparation

Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, oil, curing compound, existing paint finishes, etc. Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. ALLCOAT Epoxy Repair Mortar. Suitable mechanical treatment, such as vacuum grit-blasting, is the preferred treatment prior to application, as this ensures a mechanical key for the coating.

Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard. All dust and grease shall be removed prior to coating application. If a delay is likely to occur between blasting and application then it is recommended that a coat of ALLCOAT QD Primer be applied as holding primer to obviate flash rusting.

Priming

Apply onto the properly prepared surface a coat of ALLCOAT WB Primer for porous surfaces.

Mixing & Application

Pour the contents of the CURING AGENT tin into the BASE container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved.

Apply by brush, short piled roller or airless spray at a nominal rate of 0.3 – 0.5 kg/m²/coat, depending on overall dry film thickness required. After a minimum of 14 hours @ 20°C, but within a maximum of 48 hours, apply a second coat at the same nominal rate. If the maximum over-coating limit is exceeded, the first coat must be abraded and solvent wiped prior to application of the second coat. Should a slip resistant finish be required, then a broadcast of graded Silica Sand, or Silicon Carbide shall be made immediately after the first coat. Brush off excess aggregate prior to application of the second coat.

Size

5 litres

Colour

Blue, Dark Grey, Mid Green, Mid Grey, Tile Red

Solids content

Approx. 63%

Coverage

5m² per L per coat

Dry film thickness

125 microns at a coverage rate of 8m² per L

Pot life

40 minutes at 20°C

Touch dry time

5 hours at 20°C

Full Cured Time

Allow to cure for a minimum of 14 hours @ 20°C prior to light foot trafficking, and 24 hours @ 20°C prior to vehicular trafficking. Allow a minimum of 5 days cure @ 20°C for optimum chemical resistance.

Full chemical resistance

5 days at 20°C. Excellent chemical resistance to all acids, solvents and alkalis.

Shelf life

2 years at ambient temperature

ALLCOAT Chemical Resistant Coating TDS   ALLCOAT Chemical Resistant Coating TDS

ALLCOAT Chemical Resistant Coating Part A COSHH   ALLCOAT Chemical Resistant Coating Part A COSHH

ALLCOAT Chemical Resistant Coating Part B COSHH   ALLCOAT Chemical Resistant Coating Part B COSHH

There are no reviews yet, would you like to submit yours?

Be the first to review “Chemical Resistant Coating”

*



Related Products

You may also like…