ALLCOAT Chemical Resistant Coating - Acid Strength

A rapid curing, two pack Epoxy coating with outstanding resistance to aggressive acids, solvents, petrochemicals and alcohols

Chemical Resistant Coating – Acid Strength

Image11

5litres – £160.00

ALLCOAT Chemical Resistant Coating Acid Strength is a rapid curing, two pack Epoxy coating with outstanding resistance to aggressive acids, solvents, petrochemicals and alcohols e.g. 96% Sulphuric acid, Methyl Ethyl Ketone, Skydrol and Methanol.

Features & Benefits

  • Outstanding chemical resistance
  • Very rapid cure, even at low temperatures
  • Excellent adhesion to steel and concrete
  • Tough, durable and abrasion resistant
  • Hygienic and easily cleaned
  • Slip resistant options

Typical Uses
As an internal lining for concrete or steel storage tanks; Chemical bunds; Chemical resistant floor coating for chemical and printing works, aircraft hangers, bottling and canning factories,
pharmaceutical production, etc.

SKU: acitec1. Categories: , .

Preparation

Concrete shall be a minimum of 21 days old and/ or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, oil, curing compound, existing paint finishes, etc. Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. ALLCOAT Epoxy Repair Mortar. Suitable mechanical treatment, such as vacuum grit-blasting, is the preferred treatment prior to application, as this ensures a mechanical key for the coating.

Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard. All dust and grease shall be removed prior to coating application. If a delay is likely to occur between blasting and application then it is recommended that a coat of ALLCOAT QD Primer be applied as holding primer to obviate flash rusting.

Priming

Apply onto the properly prepared surface a coat of ALLCOAT WB Primer for porous surfaces.

Mixing & Application

Pour the contents of the CURING AGENT tin into the BASE container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved.

Apply by brush, short piled roller or airless spray at a nominal rate of 0.3 – 0.5 kg/m²/coat, depending on overall dry film thickness required. After a minimum of 14 hours @ 20°C, but within a maximum of 48 hours, apply a second coat at the same nominal rate. If the maximum over-coating limit is exceeded, the first coat must be abraded and solvent wiped prior to application of the second coat. Should a slip resistant finish be required, then a broadcast of graded Silica Sand, or Silicon Carbide shall be made immediately after the first coat. Brush off excess aggregate prior to application of the second coat.

Size

2.5 litres, 5 litres

Colour

Light Grey, Mid Blue, Mid Green, Mid Grey, Terracotta, Tile Red

Solids content

Approx. 60%

Coverage

A 5 kg pack is sufficient to coat approximately 8 m² of surface with the recommended two coat treatment, providing a typical dry film thickness of 500 microns.

Dry film thickness

75 microns at a coverage rate of 8m² per L

Pot life

30 minutes at 20°C

Full chemical resistance

5 days at 20°C. Excellent chemical resistance to all acids, solvents and alkalis.

Application temperature limits

+ 2° to 30°C

Shelf life

6 months at ambient temperature

Curing

Allow to cure for a minimum of 14 hours @ 20°C prior to light foot trafficking, and 24 hours @ 20°C prior to vehicular trafficking. Allow a minimum of 5 days cure @ 20°C for optimum chemical resistance.

Hard Dry

12 hours

Touch Dry

5 hours

ALLCOAT Chemical Resistant Coating – Acid Strength TDS   ALLCOAT Chemical Resistant Coating – Acid Strength TDS

ALLCOAT Chemical Resistant Coating – Acid Strength Part A COSHH   ALLCOAT Chemical Resistant Coating – Acid Strength Part A COSHH

ALLCOAT Chemical Resistant Coating – Acid Strength Part B COSHH   ALLCOAT Chemical Resistant Coating – Acid Strength Part B COSHH

Related Products

You may also like…