ALLCOAT Anti Slip Heavy Duty

ALLCOAT Anti Slip Heavy Duty is a 2 component, high build solvent free unpigmented polyurethane binder for surface dressing with aggregates to create non slip textured floor finishes

Anti Slip Heavy Duty

antislip

15kg – £150.75

ALLCOAT Anti Slip Heavy Duty is a 2 component, high build solvent free unpigmented polyurethane binder for surface dressing with aggregates to create non slip textured floor finishes. ALLCOAT Anti Slip Heavy Duty systems can be used in interior or exterior situations on a variety of substrates to provide high water resistant anti slip finishes.

Features & Benefits

  • Excellent slip resistant finish 
  • Extremely hard wearing 
  • Can be decorative through using coloured aggregates
  • High bond strength 
  • Will cure at temperatures down to 5°C

Typical Uses

  • Theme parks
  • Public pathways 
  • Public concourse areas 
  • Loading bays
  • Walkways around buildings and factories 
  • Demarcation of non slip areas

Preparation

To achieve the best performance from ALLCOAT Anti Slip Heavy Duty the correct surface preparation is essential. Substrates must be clean, sound, dry and free of surface laitance with a minimum strength of 25N/mm². All surfaces must be prepared by vacuum blasting or mechanical abrasion.

All surfaces to be treated with ALLCOAT Anti Slip Heavy Duty should be clean and free from loose particles, oil and grease. Surfaces should be mechanically abraded to provide a good mechanical key.

Priming

Non porous substrates require thorough preparation but do not require priming.

Porous substrates require priming with ALLCOAT Epoxy Damp Proofer at an average rate of 4 sq.m. per kg. ALLCOAT Epoxy Damp Proofer should be applied if the relative humidity of the concrete is greater than 75% RH at 4 sq.m. per kg, allow to cure for 8 – 12 hours @ 20°C

Steel decking must be clean sound and free from rust, and primed with ALLCOAT QD Primer.

ALLCOAT Anti Slip Heavy Duty is supplied as pre-weighed resin, hardener and aggregate, splitting units is not recommended.

Application

When the primed surface is tack free ALLCOAT Anti Slip Heavy Duty should be applied at the required rate as soon after mixing as possible. (Delay can result in variation in surface finish, colour and add to application problems)

Mix the resin base prior to adding the hardener and mix for a minimum of 1 minute. Add the aggregate and mix for a further 2 minutes or until a lump free consistency is produced using a drill and paddle without entraining air. Apply with trowel or pinrake to an average 2mm thickness and spike roller to remove air and aid levelling. Immediately apply surface dressing 1 – 3mm dust free aggregates, by broadcasting onto the wet ALLCOAT Anti Slip Heavy Duty resin base at a typical rate of 3kg per m². Different aggregate types will provide varying degrees of slip resistance.

Typical hard wearing aggregates would be – bauxite, granite, aluminium oxide, silicon carbide. NB. ALLCOAT Anti Slip Heavy Duty is supplied as a resin system, the aggregate for surface dressing must be ordered separately and 2 – 4 kg per m² is recommended depending on size.

Note

The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect the performance.

Size

15kg, 30kg

Colour

Dark Grey, Green, Light Grey, Mid Blue, Safety Yellow, Tile Red

Nominal Thickness

2 – 3mm

Solids content

100%

Pack make up

1 x base, 1 x hardener, aggregate

Shelf life

12 months ( base, hardener and aggregate)

Coverage rate

29 kg will cover 7 sq m @ 2mm

Pot life

10 minutes @ 20°C (from mixing)

Recoat time

4 hours @ 20°C (from mixing)

Light traffic

5 hours @ 20°C (from mixing)

Full traffic

12 hours @ 20°C (from mixing)

Full chemical cure

3 – 5 days @ 20°C (from mixing)

Slip resistance

Method BS7976 pt1-3 2002 Dry > 65, low slip potential Wet > 34, low slip potential

Temperature resistance

Up to 65°C

Chemical resistance

Good

ALLCOAT Anti Slip Heavy Duty TDS   ALLCOAT Anti Slip Heavy Duty TDS

ALLCOAT Anti Slip Heavy Duty Part A COSHH   ALLCOAT Anti Slip Heavy Duty Part A COSHH

ALLCOAT Anti Slip Heavy Duty Part B COSHH   ALLCOAT Anti Slip Heavy Duty Part B COSHH

There are no reviews yet, would you like to submit yours?

Be the first to review “Anti Slip Heavy Duty”

*



Related Products

You may also like…